Akron-RS -rekisterikilvenpidike
Akron-RS -rekisterikilvenpidike
Akron-RS -rekisterikilvenpidike
Akron-RS -rekisterikilvenpidike
Akron-RS -rekisterikilvenpidike
Akron-RS -rekisterikilvenpidike
Highsider

Akron-RS -rekisterikilvenpidike

Z 900 RS 2018-

Tuotenro. 10049584
|

2 Arvostelut

Etsi moottoripyöräsi:
OVH 79,95 € 2
54,95 € 1
Kuvaus

Akron-RS -rekisterikilvenpidike Z 900 RS 2018-

Why does it actually need a different number plate holder? Probably for "cosmetic" or visual reasons. Whatever the case, the HIGHSIDER *AKRON-RS* licence plate holder is exactly what you are looking for. Because in terms of design, it adapts perfectly to the lines of your bike.
The model-specific HIGHSIDER *AKRON-RS* holder can be mounted exactly at the original attachment points of your motorbike. For you, this means: only exchange - no drilling or cutting. The licence plate is made of sheet steel, 2 mm thick and powder-coated.
  • Vehicle-specific holder
  • Suitable for European number plates
  • Steplessly adjustable angle of inclination
  • Steplessly adjustable indicator holder
  • Slotted indicator holder for quick mounting without cable separation
  • Continuously adjustable reflector
  • simple fixing without further work steps (e.g. drilling)
  • Easy mounting of the number plate through slotted holes
  • Many different options for mounting the licence plate light
  • Reflector E-approved
Scope of delivery:
1 x HIGHSIDER *AKRON-RS* number plate holder for various vehicles
1 x HIGHSIDER AKRON-RS number plate holder
Indicator holder
1 x Reflector with adjustable holder
Mounting parts
Mounting instructions


Notes:
  • if side reflectors are fitted to your original number plate holder, these must be refitted in a suitable position or replaced with new ones
  • to avoid damage to cables, all sharp-edged feed-throughs are protected by a rubber membrane grommet
  • stepless adjustment: this allows you to adjust the plate to the desired position without drilling. To keep the plate in this position, there is an additional securing screw
  • Two rubber washers are included to secure the plate and reduce vibrations. Another rubber buffer supports the number plate on its underside.
  • the indicator brackets of the HIGHSIDER *AKRON-RS* are adjustable in width and therefore suitable for any type of accessory indicator. This allows you to adjust the position of the turn signals to suit a wide range of number plates.
  • To enable the turn signals to be mounted without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side
  • the bracket is adjustable in height and designed to allow mounting in the legally prescribed position
  • you can also adjust the position of the rear reflector individually via a slider. Adaptation to the different designs of EU number plates is done in no time at all.

Lista yhteensopivista moottoripyöristä

Dokumentit
Arvostelut (2)
Kaikki mallit
Onko sinulla vielä kysyttävää?

Onko sinulla jokin yleinen tilaustasi koskeva kysymys, haluatko antaa palautetta tai vain kertoa mielipiteesi? Olemme täällä sinua varten.

Henkilökohtaiset tiedot

Minulla on kysymys...

Valitse vaihtoehto

Valitse yhteydenottovaihtoehto

Valitse vaihtoehto

Määrittämäsi ajanjakso on virheellinen. Korjaa ajat.

Kello

Kello

Lähettämällä lomakkeen hyväksyt henkilötietojesi käsittelyn tietosuojakäytäntömme mukaisesti.

Ilmainen toimitus alkaen 119 €
Kahden vuoden palautusoikeus
Nopea toimitus
Ilmainen palautus
SearchWishlistUser AccountCartArrow LeftArrow RightArrow Right ThinIcon HomeMenuArrowCaret DownCloseResetVISAmatercardpaypalDHLHermesCheckCheck-additionalStarAdd to Shopping Cartchevron-leftchevron-rightSpinnerHeartSyncGiftchevron-upKlarnaGridListFiltersFileImagePdfWordTextExcelPowerpointArchiveCsvAudioVideoCalendar